Free passive crossover calculators, measured-data simulation, Zobel compensation, component combinations and speaker wiring tools for your next build.
MEASURE → CONNECT → SIMULATE
Build with your measured drivers.
LOCAL FILES · FREE
Import frequency response and impedance, build a passive network for each driver, and compare the filtered responses. Your files stay in this browser; they are not uploaded or added to the public library.
Start by importing your first driver’s measurements. Save your project before leaving this page.
A combined coherent SPL curve needs phase in every response file and this confirmation. Missing acoustic phase never silently becomes a summed prediction. Added delay is relative to the phase already in the file; avoid counting an existing time offset twice.
Automatic component optimizer
Start with a measured network, then tune unlocked R, L and C values toward a target. Circuit topology, driver polarity, delay and component losses stay fixed. Lock any component you want to retain.
Import acoustic phase for each driver and confirm a common measurement reference to begin.
Search method & limits
A bounded coordinate search minimizes combined-response RMS error on equally spaced log-frequency samples. Values stay within ¼–4× their starting value and L 0.001–20 mH, C 0.01–2000 µF, R 0.01–100 Ω. A load penalty covers the full shared measurement range; candidates below the requested sampled minimum are rejected. This is a local search, not a guaranteed best design. Missing ZMA uses the stated resistive approximation. It does not optimize off-axis response, phase tracking, power or standard component availability. Compare real purchased values and measure the completed loudspeaker.
∿
Your measurements, your network.
The graphs appear after valid measurements are imported. No sample driver data is substituted.
FRD / TXT / CSV: frequency Hz, SPL dB, optional phase degrees. ZMA / TXT / CSV: frequency Hz, impedance magnitude Ω, optional phase degrees. Use spaces, tabs, commas or semicolons, a decimal point and no thousands separators. Header lines before the data and comments beginning with #, !, * or ; are supported. Minimum 3 rows; maximum 50,000 rows and 2 MB per measurement. Duplicate frequencies and malformed numeric rows are rejected.
Measure the drivers on the intended baffle with a common acoustic reference and calibration. SPL data must represent the same reference drive voltage across branches. The tool interpolates magnitude and unwrapped phase on a logarithmic frequency axis, only within the overlapping imported range. With no ZMA it uses the entered constant resistance. Two-column ZMA is a magnitude-only resistive approximation, explicitly flagged.
The supported circuit is an ordered ladder of series and shunt R, L and C components per driver, connected in parallel to an ideal zero-impedance amplifier. Inductor DCR and capacitor ESR can be entered. It does not include mutual coupling, nonlinear behaviour, thermal limits, off-axis radiation, diffraction, room response, arbitrary bridge circuits, global optimisation or VituixCAD project compatibility. A saved project includes your measurements; share it only when you have permission to share that data.
Calculate a fixed two-resistor L-pad after the crossover, before the driver. Under the resistive-load assumption it reduces voltage while maintaining the entered input impedance.
Connect the two resistors
Place the series resistor between crossover output + and driver +.
Place the parallel resistor across the driver terminals, after the series resistor.
Connect driver − to the crossover return. At 0 dB use a direct connection and omit both resistors.
The continuous-power input refers to power at the pad input, not the amplifier’s total rating or the driver’s published rating. Dissipation figures are electrical estimates, not recommended resistor wattage ratings. Choose suitably rated non-inductive parts with thermal margin and verify temperature under use.
Driver impedance varies with frequency. For measured design, append a series R and a shunt R after the filter in the measured workspace, then simulate with the real impedance.
L-pad equations & reference
g = 10^(−A/20), Rs = R(1 − g), Rp = Rg/(1 − g). Input resistance is Rs + (Rp ∥ R) = R. With input power P: series resistor P(1 − g), parallel resistor Pg(1 − g), driver Pg². Zero attenuation is a special direct-connection case.
Choose a target inductance and winding geometry. Estimate whole turns, copper diameter, wire length and resistance. Air-core results use Wheeler’s multilayer approximation; magnetic cores use your supplier’s AL value.
Units, winding assumptions & core selection
Dimensions use mm and wire diameter means bare copper. Enamel thickness is added on both sides. Automatic selection tries 0.25–3.00 mm wire and chooses the smallest diameter meeting both entered targets. Air-core turns are searched up to 10,000; each candidate recalculates layer count and radial build. Wire length excludes connection leads. Copper resistivity is 0.017241 Ω·mm²/m at 20 °C.
Wheeler multilayer formula: L (µH) = 0.8a²N²/(6a + 9b + 10c), where a is mean winding radius, b winding length and c radial build, all in inches. It is an estimate for round, uniformly wound coils. Partly filled outer layers and unusual proportions reduce accuracy.
For a magnetic core, L (nH) = AL × N². Enter AL for the exact core assembly, gap and intended operating conditions. Convert datasheet units before use. The 60% window occupancy cap is a packing allowance, not a thermal or saturation limit. Core type labels do not substitute an assumed permeability. Check the supplier’s flux, bias, loss and saturation limits at the intended audio frequency and current.
A low-pass branch reduces high frequencies reaching a woofer. A high-pass branch reduces low frequencies reaching a tweeter. A two-way passive network uses both branches after the amplifier.
Electrical response
The calculators describe ideal component networks driving a fixed resistance. Impedance changes with frequency in a real driver.
Acoustic response
The sound also depends on each driver’s natural response, baffle, spacing, sensitivity and phase. A matching electrical cutoff does not guarantee a smooth acoustic crossover.
Choose the frequency
Use the driver’s measured response and manufacturer guidance. Fs alone does not establish a suitable crossover, and a tweeter’s recommended minimum depends on filter slope and power.
Start with measured frequency response and impedance, simulate the complete system, then measure the built network.
Order describes the electrical slope.
Ideal filter alignments supported here
Alignment
Far-stopband slope
Branch level at design frequency
Q
First order
6 dB/octave
−3.01 dB
Not applicable
Second-order Butterworth
12 dB/octave
−3.01 dB
1/√2 ≈ 0.7071
Second-order Linkwitz–Riley
12 dB/octave
−6.02 dB
0.5
Third-order Butterworth
18 dB/octave
−3.01 dB
Third-order polynomial
Fourth-order Butterworth
24 dB/octave
−3.01 dB
Fourth-order polynomial
Fourth-order Linkwitz–Riley
24 dB/octave
−6.02 dB
Squared second-order Butterworth response
The quoted slope is asymptotic, not the attenuation one octave from the design frequency. In an ideal coincident two-way second-order system, one branch is reversed for summation; actual driver polarity must be validated from the measured acoustic response.
These tools do not predict the combined acoustic response, lobing or time alignment.
The components are only part of the design.
Inductors
Inductance is entered in mH. Coil resistance, current capacity and core behaviour affect the built filter; those losses are not included here.
Capacitors
Capacitance is entered in µF. Use suitable non-polar parts with adequate voltage rating. Tolerance and ESR affect the result.
Driver impedance
Enter the resistive load used for the approximation. Nominal impedance and DC resistance are different quantities. Prefer measured impedance near the intended crossover.
Connections used by these calculators
First-order low-pass: series inductor, then driver.
First-order high-pass: series capacitor, then driver.
Second-order low-pass: series inductor, capacitor in parallel with the driver.
Second-order high-pass: series capacitor, inductor in parallel with the driver.
Each branch connects across the amplifier output. A shunt component is connected across the driver terminals. These are parallel two-way branches, not a series crossover.
Build the whole signal path.
Choose the woofer and tweeter crossover alignments separately, then select the correction sections you want on each driver. The complete loaded circuit is solved together; its response includes interactions between sections.
Ideal components are assumed. Loads are constant resistance unless a branch has Zobel enabled; that branch uses its entered Re + jωLe driver model. The plots show electrical voltage, not acoustic SPL. No acoustic sum, diffraction response, power ratings or driver protection is inferred. Refine with measured driver impedance and response before building; this tool does not export a VituixCAD project.
Calculate both branches with separate woofer and tweeter load values.
Components → filter response
Check one branch at a time. For a second-order branch, both L and C are needed.
Target a response peak.
Design a parallel RLC network placed in series with the driver. Choose a capacitor value to set the notch width, then calculate the inductor and damping resistor.
How to connect the network
Connect R, L and C in parallel between the same two nodes.
Insert this parallel network in the positive lead to the driver. Connect the driver’s negative terminal to the amplifier return.
The graph treats this as a standalone correction network with an ideal amplifier and a resistive driver. An existing crossover changes the result.
This calculator does not design a series RLC impedance trap across a driver. That is a different network and does not produce this voltage notch with an ideal zero-resistance amplifier.
Notch equations and assumptions
With centre frequency f₀, selected capacitor C and attenuation A: L = 1/((2πf₀)²C), R = Rload(10^(A/20) − 1). At resonance the parallel network impedance is R. At each frequency, Y = 1/R + j(ωC − 1/(ωL)), Z = 1/Y, H = Rload/(Rload + Z).
R is the resistor in the network, not the driver impedance. L is in H and C in F in the equations. Changing C changes the width while the calculator keeps the same centre frequency and ideal depth. Inductor resistance, capacitor ESR, component tolerance, driver impedance and interaction with a crossover are omitted. Use measured response to choose the peak and verify the built circuit.
Balance the baffle-step transition.
Calculate a passive R ∥ L shelf in series with the driver. It attenuates the higher-frequency region relative to bass; it does not boost bass output.
How to connect the network
Connect the resistor and inductor in parallel between two nodes.
Insert that parallel pair in series with the driver’s positive lead. The negative terminal returns to the amplifier.
At low frequencies the ideal inductor bypasses the resistor; at high frequencies the resistor sets the attenuation.
The width estimate is a starting point for a conventional front baffle, not a diffraction simulation. Baffle shape, driver position and nearby walls affect the acoustic result. Select the amount from measurements and placement; full 6 dB compensation is not always appropriate.
Baffle-step equations and references
Width estimate: f ≈ 115 / W, with W in metres. For attenuation A, g = 10^(−A/20), R = Rload(1/g − 1), L = R√g/(2πf). The chosen f is the midpoint in dB of the ideal electrical shelf, not its pole or zero. Pole: fp = Rg/(2πL). Zero: fz = R/(2πL). At f = √(fp fz), gain is −A/2 dB.
Electrical response: H = Rload/(Rload + (R ∥ jωL)). The plot shows this correction alone, not predicted acoustic response. Zero compensation means a direct connection and no added network. Coil resistance, component tolerance, power dissipation, frequency-dependent driver impedance and interaction with the crossover are omitted.
Passive speaker crossover calculatorsChoose passive speaker crossover order and alignment, calculate L/C values, then add L-pad, notch and baffle-step correction in a complete network.
Measured crossover design and optimizerImport FRD and ZMA driver measurements, build series/shunt RLC branches and optimize unlocked components. Preserve reference settings and save your project.
Inductor winding calculatorEstimate speaker crossover inductor turns, wire diameter, winding geometry and DCR. Use air-core Wheeler estimates or a magnetic core supplier’s AL value.
Zobel Impedance Compensation CalculatorCalculate a speaker driver Zobel resistor and capacitor from DC resistance and inductance, with connection diagram and ideal resistor-loss estimate.
Series & Parallel Component CalculatorCombine crossover capacitors, inductors or resistors in series or parallel, and find ideal one- or two-part E12/E24 combinations for a target value.
Speaker Wiring & Impedance CalculatorPlan identical loudspeaker drivers in series and parallel, including dual voice coils, with nominal amplifier load, wiring diagram and ideal power sharing.