Sealed
The trapped air adds stiffness. Volume and driver parameters set resonance and damping. A simple starting point for evaluating Qtc and bass roll-off.
Free speaker box calculators for sealed, ported, band-pass, passive-radiator and open-baffle designs. Plan the panels and export cabinet outlines.
Use measured T/S parameters, then choose a target Qtc greater than the driver’s Qts. Qtc ≈ 0.707 gives a maximally flat ideal second-order high-pass response; it is not always the best choice for your room or target bass response.
Estimate low-frequency cancellation using a pair of opposite-polarity point sources. Enter an effective front-to-rear path length, or use a rough flat-baffle geometry estimate. Example values are calculator inputs, not a named driver specification.
This is a low-frequency design aid, not a finite-baffle diffraction simulation. It excludes actual cone/basket radiation, edge diffraction, room reflections, radiation loading, U/H-frame cavity resonances and excursion limits. Measure the driver on its intended baffle before choosing EQ or crossover values.
Two opposite point sources: |H| = 2|sin(πfD cos θ / c)|, with D in metres and c = 343 m/s. On axis: unity at c/(6D), first peak at c/(2D), first null at c/D. These are point-model landmarks, not predicted resonances of a real rectangular baffle. The model is most useful when kD = 2πfD/c is much less than 1.
The geometric shortcut uses D = 2 × the shortest driver-centre-to-edge distance. This is a rough path estimate, not an exact acoustic path or a driver-fit check. Use an independently established effective D where possible. Optional driver magnitude = x² / √((1 − x²)² + (x/Qts)²), x = f/Fs; the result is multiplied by the cancellation factor. Air loading and voice-coil inductance are excluded.
Reference: Linkwitz Lab: dipole models and their limitations ↗. Calculations and plots are original; no source drawings or files are reproduced.
Enter measured T/S parameters, choose net volume and Fb, and compare the ideal response. This is a manual design tool; it does not choose an optimum alignment.
Port length assumes one flanged and one free end. The graph combines cone and vent with their phase relationship. Excludes voice-coil inductance, room gain, cabinet leakage, thermal compression, excursion and air velocity. Port Q is a simplified loss input, not a measured cabinet specification.
The driver sits between rear and front chambers. Choose the arrangement below; chamber tunings are inputs, while the complete system passband is calculated.
Fourth order has one vent group; sixth order has two. Diameter and count apply to each group. For series tuning, the rear reference Fb uses the rear chamber alone; coupling shifts the system resonances. Lengths are preliminary one-flanged-end estimates. An internal connecting vent may need different end corrections. Band edges are −3 dB relative to the model peak, not the individual chamber tunings.
Estimate the required total moving mass and mass adjustment for each identical radiator, including its suspension stiffness. This estimates the radiator/box tuning with the active cone held fixed; verify the assembled system by impedance measurement.
Mms and Cms must use consistent manufacturer definitions and include the current installed weights. Air density 1.18 kg/m³ and speed of sound 343 m/s. Added mass must be within the manufacturer’s allowed range. Radiator excursion, rocking modes, damping and maximum SPL are not predicted. A negative adjustment means mass must be removed; do not remove structural moving parts.
Start from a chosen net volume and tuning frequency. This Helmholtz calculator does not choose an optimum vented alignment or predict port air velocity.
Speed of sound: 343 m/s. Simple straight circular ports with separated ends are assumed. Flares, bends, nearby walls and large aspect ratios alter tuning; measure and trim the finished port. The reported length includes the panel thickness if the tube starts at the outer baffle face. Reserve actual outside port displacement, not just the bore’s air volume.
A rectangular box with equal wall thickness and butt joints. Side panels span full height and depth; top and bottom fit between the sides; front and back fit within that frame.
Finished panel sizes exclude saw kerf, rebates, glue gaps, veneer and machining allowances. Check the joint layout, driver cutout, mounting depth and clearances before cutting. This is not a structural assessment or a nesting plan.
Plan a rectangular, equal-thickness cabinet with front-panel cutouts. Rotate the preview, inspect the assembly and export full-size panel outlines. This designer handles fabrication geometry; use the acoustic calculators to choose your enclosure volume.
The trapped air adds stiffness. Volume and driver parameters set resonance and damping. A simple starting point for evaluating Qtc and bass roll-off.
The box and port form a resonator. Tuning alone does not establish a good alignment; driver parameters, losses, excursion and port velocity need a full system simulation.
The radiator tool includes moving mass, suspension compliance and box stiffness. Check displacement separately. Horns and transmission lines need different models.
Manufacturer example enclosures can be useful references. Check the exact impedance, revision and application; a cabinet designed for a similarly named driver may not suit yours.
Net acoustic volume excludes solid driver parts, braces and the complete port passage. Measure actual displacement and keep separate chambers separate.
Panel thickness alone does not determine rigidity. Place braces, preserve driver and port clearance, seal joints, and use suitable gaskets.
Lining and stuffing change losses and apparent acoustic behaviour. Their effect is not a fixed percentage added to the volume in these calculators. Keep vents clear.
Baffle width and driver placement affect diffraction and the crossover. Measure the drivers on the intended cabinet before finalising the network. Open measured crossover workspace →
These calculations describe small-signal approximations and are not driver protection or power-handling guarantees.
Browse all speaker design tools & guides →