A quick look at
your sound.
Your PC plays. Your phone listens. Compare one change at a time.
Use this for broad response and before/after checks. A built-in phone microphone has unknown accuracy. Precision crossover work needs a calibrated microphone and verified timing.
Instructional videosSix simple walkthroughs · 25–40 seconds each
Phone Quick measure: pair & compare
Silent, captioned guides to physical setup and the website’s controls. Example values, pairing states and synthetic responses are for demonstration. Press Play, or read the steps below.
Read the video steps
- 1Pair phone
- 2Place & prepare
- 3Run sweep
- 4Compare response
Pair your phone.
Connect the PC output to your amplifier. Put the phone and PC on the same Wi-Fi, then scan the QR code with your phone camera.
Open on your phone
Open pairing linkPrivate link · expires here after 10 minutes. Share only with your phone.
One last pairing step
Your phone shows a pairing reply. Copy it to this PC using your usual way of sharing text, paste it here and connect. You only do this once per session.
Connected phone
Keep the setup simple.
Place the phone steadily, about 0.5–1 m in front of the complete loudspeaker. Leave the microphone opening clear. Use the same position and volume for each comparison. Tap Allow microphone, then Ready to measure on the phone.
Choose PC output & optional microphone correction
If output selection is unavailable, use the PC sound settings. A browser output does not automatically route through your DAW. Avoid Bluetooth for measurement. Use your own microphone’s verified response-error file; values are subtracted within its covered band. No phone-model calibration is invented.
Optional: match an external level reading
First play the 500 Hz–2 kHz white noise and note a steady Z / unweighted reading with the meter and phone at the same position. Then capture that reading at unchanged gain and volume. Available only when all three browser processing controls report off. This estimates level for this session; it does not certify phone accuracy.
Run your sweep.
A full loudspeaker is the easiest first test. Keep its protective crossover in place. Start with low amplifier volume.
Digital test level
The short timing sounds stay within the selected test band. Amplifier gain determines the actual acoustic level.
Both pages must stay open and visible. The phone sends its lossless recording directly to this PC after the sweep. A permission or connection problem will show the next step above.
Your phone is the microphone.
The PC plays through your loudspeaker. Nothing plays from this phone.
Return this reply to the PC
Copy the reply, share it to the PC, then paste into Reply from your phone and click Connect phone.
Microphone is off.
- Rest the phone steadily in front of the speaker.
- Keep the microphone opening uncovered; use the same orientation.
- Keep this screen visible. Do not switch apps during recording.
Your response.
Time gate, graph scale & input checks
Impulse time is shown relative to the largest peak. End the gate before a visible reflection; a phone can blur arrivals. This timing is for window selection, not phase alignment between drivers.
Gate, correction and smoothing apply to both Before and After curves. Graph limits only change the display. The phone’s frequency response, hidden processing and placement remain possible errors. Marker clock correction is an estimate, not validated precision timing.
Export or continue in crossover design
Exports contain the current response, not the difference graph. FRD contains frequency and magnitude only: phase is deliberately omitted. Original WAV is unchanged by graph processing.
Privacy, connection help & measurement limits
Microphone access starts only when you tap Allow microphone. Lossless samples travel through an encrypted direct connection between the paired devices; audio is not uploaded to SpeakerFoundry. Recordings and your Before curve stay in this tab unless you save or export them. Ending a session stops capture and playback; reload or close the tab to clear its results.
Automatic pairing, when enabled, stores short-lived connection descriptions, not audio. Manual pairing uses a QR link and one reply; the link includes local connection details, so share it privately. No public STUN or TURN relay is used. Devices must be on the same Wi-Fi without client/guest isolation; some firewalls and browsers prevent direct connections. If pairing fails, use the external-source recording workflow instead.
This beta has synthetic signal and software checks. Phone capture and acoustic accuracy require real-device validation. A level reference does not make the phone an IEC-compliant sound-level meter. No phone-model correction database or numerical accuracy grade is claimed.