Tannoy HPD 385A
Tannoy HPD 385A coaxial reference. 8 ohm. Checked specification facts, historical technical sources and CAD access status.
Driver specifications
- Brand
- Tannoy
- Type
- Coaxial
- Collection
- Vintage reference
- Nominal size
- 15 inches / 385 mm — original nominal designation
- Nominal impedance
- 8 Ω
- Diaphragm material
- See source
- Overall diameter
- Not established in reviewed drawing
- Baffle cutout
- See original recess and sub-baffle drawings below
- Mounting depth behind flange
- Not established in reviewed drawing
- Source checked
- 2026-10-16
Dimensions below distinguish the original sub-baffle aperture from the front recess. Check the exact drawing and your physical driver before machining.
Used in loudspeaker
Documented examples for this exact driver. Factory products, manufacturer kits and designer DIY projects are identified separately.
No documented loudspeaker uses have been added for this driver yet. This means the reference list is incomplete, not that the driver has never been used.
These examples are not a compatibility guide, replacement recommendation or endorsement. OEM variants, production changes and modified speakers may use different parts. Check the original documentation for the exact loudspeaker version.
Construction, mounting & original reference
Open a section for documented details and its original source.
Original integrated drive system
- Exact model
- HPD 385A; 8 Ω nominal
- Nominal designation
- 385 mm (15 inches), as printed; not overall frame diameter
- LF section
- Girdacoustic reinforcing ribs on the LF cone; 50 mm copper-wire voice coil
- HF section
- Horn-loaded compression driver; 50 mm duralumin diaphragm and 50 mm aluminium-wire voice coil
These details describe the original integrated assembly; restored or reconed units may differ.
Original rating and crossover conditions
- Power handling
- 85 W continuous programme in the original table; no modern AES rating inferred
- Sensitivity reference
- 3 W input at 400 Hz produces 96 dB at 1 m in an anechoic environment
- Original crossover
- 1000 Hz at 12 dB/octave, with the original network
- HF horn cutoff
- 500 Hz horn cutoff; this is not the recommended crossover frequency
- Shipping weight
- 14 kg; not net driver mass or moving mass
Sensitivity is preserved in its original input-power form; it is not relabelled as a 1 W or 2.83 V specification.
Recess mounting and sub-baffle
- Original enclosure references
- Arden / Berkeley equivalents in this manual
- Sub-baffle opening
- 346 mm circular opening in Figure 7; not the complete front-baffle recess
- Fixing layout
- 370 mm pitch circle; four illustrated fixing positions
- Sub-baffle hole diameters
- Figure 7 lists 8 mm for the 385, 8 mm in Cheviot / 6 mm in Devon for the 315, and 6 mm for the 295
- Fastener type
- ¼ BSW tee nuts for the 385; 2 BA for the 315 and 295
The sub-baffle aperture, front recess and nominal size are different dimensions. Confirm the original drawing, unit and fastener before machining. Overall frame diameter and depth remain unknown here.
Original network controls
- Energy
- Five positions; adjusts the HF section over approximately 1–20 kHz
- Roll-off
- Acts above approximately 5 kHz
- Initial reference
- Both controls at the original Level position
These are controls on the original network, not interchangeable settings for a newly designed crossover.
Thiele/Small parameters
Historical T/S values, including the original tabulated resonance, remain withheld pending independent exact-variant corroboration. Published system ratings are kept with their original conditions.
CAD origin and access
No verified CAD resource
Original HPD 385A coaxial integrated drive system with an 8-ohm nominal impedance, separate LF and HF coils and its original crossover network. Sub-baffle dimensions are identified separately from front-baffle geometry; current stock and a complete CAD model are not established.
No verified CAD link is offered for this record.
Technical sources
View original technical reference ↗Historical HPD integrated drive system. Used stock, original parts, reconing and condition require individual confirmation.
Check the exact revision and original drawing before purchasing or machining. Published specifications may change. Complete geometry and live stock are not certified by this library.