Tang Band W6-2090
Tang Band W6-2090 woofer reference, with manufacturer specifications and an official product photograph. Glass Fiber diaphragm and ferriter motor.
Manufacturer product photographDriver specifications
- Type
- Woofer
- Nominal size
- 6.5" nominal manufacturer designation
- Nominal impedance
- 2 Ω
- Diaphragm material
- Glass Fiber
- Sensitivity
- 88 dB; 1 W / 1 m
- Rated power input
- 30 W; manufacturer designation
- Maximum power input
- 60 W; distinct from rated power
- Response endpoints
- 50–5000 Hz; no tolerance specified
- Mounting dimensions
- Consult the complete manufacturer drawing
- Source checked
- 2026-10-16
Manufacturer rated power input; test standard, band, filter and duration are not specified in the table. Published frequency-response endpoints; no tolerance specified. These endpoints are not recommended crossover frequencies.
Construction, mounting & original reference
Open a section for documented details and its original source.
Construction and rated performance
- Nominal size
- 6.5"
- Diaphragm
- Glass Fiber
- Surround
- Rubber
- Magnet
- Ferriter
- Sensitivity
- 88 dB at 1 W / 1 m
- Rated power input
- 30 W
- Maximum power input
- 60 W; distinct from rated power
- Voice-coil diameter
- 25.4 mm
- Published response range
- 50-5K Hz
- Air gap height
- 4 mm
- Ferrofluid
- No
- Published Zo
- 17 Ω
Published power and frequency limits retain their source conditions. They are not a recommended filter or safe operating-level prescription.
Tang Band official product page ↗ · Current product table and linked manufacturer PDF
Measurement conditions and fit
- Sensitivity reference
- 1 W / 1 m; not 2.83 V / 1 m
- Levc
- Measurement frequency is not specified
- Sd conversion
- Manufacturer m² converted to cm²
- Cms conversion
- Manufacturer µm/N converted to mm/N
- Mounting dimensions
- Consult the complete original drawing; frame diameter, baffle opening and behind-flange clearance have not been separately verified
- Current catalogue status
- Product page available at the check date; live stock is not asserted
Verify the current model revision and mounting clearances before machining.
Tang Band official product page ↗ · Current product table and linked manufacturer PDF
Source discrepancy: Sd / effective piston area
- Product page
- 0.014 m² (140 cm²)
- Other official source
- 0.0014 m² (14 cm²) in the linked manufacturer PDF
- Library treatment
- Sd / effective piston area withheld pending manufacturer clarification
The original PDF table was visually reviewed. A likely decimal issue is not silently corrected.
Tang Band official product page ↗ · Current product table and linked manufacturer PDF
Source discrepancy: Levc / inductance
- Product page
- 0.045 mH
- Other official source
- 0.45 mH in the linked manufacturer PDF
- Library treatment
- Levc / inductance withheld pending manufacturer clarification
The original PDF table was visually reviewed. Measurement frequency is not inferred and neither conflicting value is selected.
Tang Band official product page ↗ · Current product table and linked manufacturer PDF
Thiele/Small parameters
Official product-table values. Sd is converted from m² to cm² and Cms from µm/N to mm/N. Le is the published Levc; measurement frequency is not stated. Unlisted fields stay unknown. Unresolved source discrepancies are withheld and documented below; no alternative value is substituted.
- Fs · resonance
- 50 Hz
- Qts · total Q
- 0.49
- Qes · electrical Q
- 0.55
- Qms · mechanical Q
- 4.1
- Vas · equivalent volume
- 13.11 L
- Re · DC resistance
- 1.8 Ω
- BL · force factor
- 4.14 N/A
- Mms · moving mass
- 16.96 g
- Cms · compliance
- 0.61399 mm/N
- Xmax · published excursion
- 4.8 mm
Only populated, resolved source fields are listed. Published X-max value; excursion convention is not independently redefined. Confirm the manufacturer’s convention before estimating displacement. These are reference specifications, not measurements of your individual driver.
Sources & availability
Tang Band official product page ↗ · Manufacturer PDF datasheet ↗
Listed in Tang Band’s current catalogue. Confirm stock, production revision and complete mounting drawing with the manufacturer.