Altec Lansing 902-8B
Original Altec 902-8B compression-driver reference with a tangential aluminium diaphragm, aluminium ribbon coil and ferrite motor. The shared sheet’s minimum-impedance wording, horn-loaded test conditions and conflicting depth figures remain explicit.
Driver specifications
- Brand
- Altec Lansing
- Type
- Compression
- Nominal size
- High-frequency compression driver
- Nominal impedance
- The shared original sheet specifies minimum impedance options of 8 Ω or 16 Ω. It does not label them nominal impedance; a nominal value is not inferred solely from the model suffix.
- Minimum impedance — shared sheet
- 8 or 16 Ω; not described as nominal impedance
- Original document
- Altec AL-2402, Revision 6, copyright 1987, print code 587-1M; archive circa-1986 label is approximate
- Voice-coil diameter / construction
- 44.45 mm / Aluminium Edgewound ribbon
- Diaphragm
- Tangential aluminium diaphragm
- Magnet material
- Ferrite
- Power rating
- 15 W. 15 W continuous pink noise, band-limited 500–20000 Hz, measured on an Altec 511B horn. Not relabelled AES power.
- Published frequency range
- 500–20000 Hz. Original 500–20000 Hz endpoints; sheet specifies use with appropriate horns and dividing networks. No numerical flatness tolerance is stated.
- Pressure sensitivity
- 106 dB SPL. 1 W pink-noise input, band-limited 1200–5000 Hz, measured 1 m from the mouth of an Altec 511B horn. A horn-loaded rating, not bare-driver sensitivity.
- Horn / crossover combinations
- Original source names 511B at 500 Hz, 811B at 800 Hz and MR931-12 at 1200 Hz, with appropriate dividing networks; not an unrestricted crossover recommendation.
- Magnet mass
- 40 oz; not moving mass Mms
- Magnetic-gap flux
- 1.8 T. Original specification-table value 1.8 T, equivalent to 18000 gauss. Engineering prose contains an inconsistent unit; the table value is retained. Not force factor BL.
- Driver mass
- 6.375 lb
- Overall diameter
- 139.7 mm
- Magnetic structure mass
- 5.75 lb; distinct from magnet and moving mass
- Attachment studs
- Two ¼-20 × 1-inch studs, 180° apart on 1½-inch (38.1 mm) centres, as stated in the original table. Confirm thread, attachment geometry and tolerances against the original drawing before machining.
- Original replacement diaphragm
- 34647 (historical part number, not a current-stock claim)
- Mounting depth behind flange
- Not established
- Source checked
- 2026-10-09
Overall diameter 5.50 inches (139.7 mm). Depth is inconsistent within the source: table 2⅝ inches (66.675 mm), drawing total 2.69 inches (68.326 mm) and separate body dimension 2.60 inches (66.04 mm), excluding the projecting studs. No single mounting-depth value or complete CAD geometry is asserted.
Construction, mounting & original reference
Open a section for documented details and its original source.
Original repair part
- Factory replacement diaphragm
- 34647 for 902-8B
- Assembly
- Replaceable tangential aluminium diaphragm / edgewound aluminium ribbon coil
Historical factory part identification only. Current stock, aftermarket equivalence and compatibility with modified units are not established.
Horn attachment
- Mounting studs
- Two ¼-20 × 1-inch studs, 180° apart
- Centre spacing wording
- The original table specifies 1½-inch centres; use the dimensioned drawing to establish the mounting layout
Body depth values conflict within the sheet and remain unlisted as a machining-ready mounting depth.
Original Altec 902-8B / 902-16B literature ↗ · Pages 1–2
Construction & original application
- Phase plug
- Tangerine design with 13 radial slots
- Loading cap
- Original design includes a loading cap for the documented crossover applications
- Original horn examples
- 511B at 500 Hz; 811B at 800 Hz; MR 931-12 at 1200 Hz
- Original finish
- Gray Hammertone enamel with black rubber boot
The named horn and dividing network remain part of the application conditions.
Original Altec 902-8B / 902-16B literature ↗ · Pages 1–2
Identify the reference
- Original publication
- AL-2402, revision 6, copyright 1987, print code 587-1M
- Exact variant
- 902-8B; replacement diaphragm 34647 is listed separately from the other impedance version
This is document identification, not an individual manufacturing date. The source table labels its impedance figures as minimum impedance.
Thiele/Small parameters
Historical T/S values remain unlisted until corroborated by two credible sources for this exact original variant. Later revisions, replacements and reconed units are not substituted.
Technical sources & availability
Original Altec literature at Lansing Heritage ↗
Out-of-production original Altec reference. Used-unit availability, original parts, reconing and condition require individual confirmation.
Confirm the exact variant and original mounting drawing before machining.