SpeakerFoundry
VINTAGE DRIVER REFERENCE

Altec Lansing 902-16B

Original Altec 902-16B compression-driver reference with a tangential aluminium diaphragm, aluminium ribbon coil and ferrite motor. The shared sheet’s minimum-impedance wording, horn-loaded test conditions and conflicting depth figures remain explicit.

PDF / documentation ↗

Driver specifications

Brand
Altec Lansing
Type
Compression
Nominal size
High-frequency compression driver
Nominal impedance
The shared original sheet specifies minimum impedance options of 8 Ω or 16 Ω. It does not label them nominal impedance; a nominal value is not inferred solely from the model suffix.
Minimum impedance — shared sheet
8 or 16 Ω; not described as nominal impedance
Original document
Altec AL-2402, Revision 6, copyright 1987, print code 587-1M; archive circa-1986 label is approximate
Voice-coil diameter / construction
44.45 mm / Aluminium Edgewound ribbon
Diaphragm
Tangential aluminium diaphragm
Magnet material
Ferrite
Power rating
15 W. 15 W continuous pink noise, band-limited 500–20000 Hz, measured on an Altec 511B horn. Not relabelled AES power.
Published frequency range
500–20000 Hz. Original 500–20000 Hz endpoints; sheet specifies use with appropriate horns and dividing networks. No numerical flatness tolerance is stated.
Pressure sensitivity
106 dB SPL. 1 W pink-noise input, band-limited 1200–5000 Hz, measured 1 m from the mouth of an Altec 511B horn. A horn-loaded rating, not bare-driver sensitivity.
Horn / crossover combinations
Original source names 511B at 500 Hz, 811B at 800 Hz and MR931-12 at 1200 Hz, with appropriate dividing networks; not an unrestricted crossover recommendation.
Magnet mass
40 oz; not moving mass Mms
Magnetic-gap flux
1.8 T. Original specification-table value 1.8 T, equivalent to 18000 gauss. Engineering prose contains an inconsistent unit; the table value is retained. Not force factor BL.
Driver mass
6.375 lb
Overall diameter
139.7 mm
Magnetic structure mass
5.75 lb; distinct from magnet and moving mass
Attachment studs
Two ¼-20 × 1-inch studs, 180° apart on 1½-inch (38.1 mm) centres, as stated in the original table. Confirm thread, attachment geometry and tolerances against the original drawing before machining.
Original replacement diaphragm
34852 (historical part number, not a current-stock claim)
Mounting depth behind flange
Not established
Source checked
2026-10-09

Overall diameter 5.50 inches (139.7 mm). Depth is inconsistent within the source: table 2⅝ inches (66.675 mm), drawing total 2.69 inches (68.326 mm) and separate body dimension 2.60 inches (66.04 mm), excluding the projecting studs. No single mounting-depth value or complete CAD geometry is asserted.

Construction, mounting & original reference

Open a section for documented details and its original source.

Original repair part
Factory replacement diaphragm
34852 for 902-16B
Assembly
Replaceable tangential aluminium diaphragm / edgewound aluminium ribbon coil

Historical factory part identification only. Current stock, aftermarket equivalence and compatibility with modified units are not established.

Original Altec 902-8B / 902-16B literature ↗ · Page 1

Horn attachment
Mounting studs
Two ¼-20 × 1-inch studs, 180° apart
Centre spacing wording
The original table specifies 1½-inch centres; use the dimensioned drawing to establish the mounting layout

Body depth values conflict within the sheet and remain unlisted as a machining-ready mounting depth.

Original Altec 902-8B / 902-16B literature ↗ · Pages 1–2

Construction & original application
Phase plug
Tangerine design with 13 radial slots
Loading cap
Original design includes a loading cap for the documented crossover applications
Original horn examples
511B at 500 Hz; 811B at 800 Hz; MR 931-12 at 1200 Hz
Original finish
Gray Hammertone enamel with black rubber boot

The named horn and dividing network remain part of the application conditions.

Original Altec 902-8B / 902-16B literature ↗ · Pages 1–2

Identify the reference
Original publication
AL-2402, revision 6, copyright 1987, print code 587-1M
Exact variant
902-16B; replacement diaphragm 34852 is listed separately from the other impedance version

This is document identification, not an individual manufacturing date. The source table labels its impedance figures as minimum impedance.

Original Altec 902-8B / 902-16B literature ↗ · Page 2

Thiele/Small parameters

Historical T/S values remain unlisted until corroborated by two credible sources for this exact original variant. Later revisions, replacements and reconed units are not substituted.

Technical sources & availability

Original Altec literature at Lansing Heritage ↗

Out-of-production original Altec reference. Used-unit availability, original parts, reconing and condition require individual confirmation.

Confirm the exact variant and original mounting drawing before machining.

Search Altec references → · Vintage driver directory →