SpeakerFoundry
VINTAGE DRIVER REFERENCE

Altec Lansing 804A

Original Altec 804A 16 Ω compression driver with an aluminium diaphragm and edgewound aluminium ribbon coil. Its 30 W rating requires the documented horn/network combination; sensitivity retains the original warble-band, trumpet and 4 ft test conditions.

PDF / documentation ↗

Driver specifications

Brand
Altec Lansing
Type
Compression
Nominal size
High-frequency compression driver
Nominal impedance
16 Ω
Original document
Altec catalogue sheet AL-1477; undated, archive describes circa 1968 (approximate)
Voice-coil diameter
44.45 mm
Voice-coil material / construction
Aluminium / Edgewound ribbon
Diaphragm / cone material
Aluminium
Diaphragm diameter / suspension
57.15 mm / Tangential compliance
Power rating
30 W. Original 30 W rating with an Altec N-500D or N-800D dividing network. No modern AES/RMS noise-test protocol is stated.
Published frequency range
500–22000 Hz. 500–22000 Hz with a 511A or 511B horn and N-500D network. The 811B horn with N-800D network is specified for 800–22000 Hz. No numerical flatness tolerance is supplied.
Pressure sensitivity
109.5 dB SPL. 1 W input; warble-frequency band 500–2500 Hz; measured 4 ft (1.2192 m) from the mouth of a 30-inch trumpet. Pressure reference 0.0002 dyne/cm² (20 μPa). Not a 1 m or bare-driver rating.
Full-power SPL
124.2 dB SPL. Published SPL with 30 W input under the same 4 ft, 30-inch trumpet and 500–2500 Hz warble-frequency conditions.
Horn / crossover combinations
500 Hz requires N-500D and 511A/511B; 800 Hz uses N-800D and 811B. These are source-specific horn/network combinations, not unrestricted crossover recommendations.
Magnet weight
13 oz
Magnet-weight conditions
Original table magnet weight, distinct from whole-driver or magnetic assembly mass and moving mass Mms.
Magnetic-gap flux density
13000 gauss. Original table magnetic-gap flux; the engineering text specifies this as a minimum. Not the T/S force factor BL.
Overall frame diameter
114.3 mm
Mounting depth behind flange
Not established from a dimensioned original drawing
Source checked
2026-10-08

Overall diameter 4½ inches converted at 25.4 mm/in. Behind-flange mounting depth, horn attachment geometry and machining tolerances are not established from a dimensioned drawing.

Construction, mounting & original reference

Open a section for documented details and its original source.

Construction
Diaphragm diameter
2¼ inches (57.15 mm), aluminium with tangential compliance
Voice coil
Edgewound aluminium ribbon, 1¾ inches (44.45 mm) diameter
Original finish
Altec Green

Original Altec 802D / 804A literature ↗ · Pages 1–2

Original service provision
Replaceable assembly
Diaphragm and voice-coil assembly; factory design includes self-centring alignment dowels

The original sheet documents this service provision. A currently available replacement part and its compatibility have not been established.

Original Altec 802D / 804A literature ↗ · Pages 1–2

Historical horn / crossover guidance
500 Hz combination
511A or 511B horn with N-500D dividing network
800 Hz combination
811B horn with N-800D dividing network

Original combinations for these 16-ohm references. They are not a general crossover limit for any horn or replacement diaphragm.

Original Altec 802D / 804A literature ↗ · Page 2

Identify the reference
Document context
Archive describes circa 1968 literature, catalogue AL-1477
Variant identification
804A, 16 ohms; keep separate from 802D

A document date does not establish when an individual unit was manufactured.

Original Altec 802D / 804A literature ↗ · Archive context and CAT. NO. AL-1477

Thiele/Small parameters

Historical T/S values remain unlisted until corroborated by two credible sources for this exact original variant. Values from later Altec revisions, modern replacements and individual recones are not substituted.

Technical sources & availability

Original Altec literature at Lansing Heritage ↗

Out-of-production original Altec reference. Used-unit availability, original parts, reconing and condition require individual confirmation.

The original sheet remains at its external source. Confirm the exact unit and original mounting drawing before machining.

Search Altec references → · Vintage driver directory →