Altec Lansing 803B
Altec 803B vintage 16-ohm woofer: original basket, cloth surround, driver weight, four-point mounting and cabinet/network references.
Driver specifications
- Brand
- Altec Lansing
- Type
- Woofer
- Nominal size
- 15 inches — nominal
- Nominal impedance
- 16 Ω
- Original document
- Altec catalogue sheet AL-1411-2; publication date not stated
- Voice-coil diameter
- 76.2 mm (3 inches)
- Voice-coil material / construction
- Copper / Edgewound ribbon
- Frame material
- Cast aluminium
- Cone material
- Moulded fibre
- Surround material
- High-compliance cloth
- Magnet material
- Alnico V
- Continuous power
- 30 W. Continuous power rating in the original sheet. No AES/RMS noise-test method or bandwidth is given; this is not relabelled as an AES rating.
- Pressure sensitivity
- 99 dB SPL. Published pressure sensitivity on axis at 4 ft (1.2192 m), with 1 W input. Signal bandwidth and enclosure are not specified. This is not a 1 m rating.
- Full-power SPL
- 114 dB SPL. Published SPL at 4 ft using the full 30 W continuous rating, separate from the 1 W sensitivity.
- Published frequency range
- 20–1600 Hz. Published frequency-response endpoints in the original sheet; no response tolerance, measurement enclosure or modern test standard is specified.
- Magnet weight
- 2.4 lb. Magnet weight in the original table; not complete magnetic assembly weight, driver mass or moving mass Mms.
- Magnetic gap flux density
- 12000 gauss. Original magnetic-gap flux density, in gauss; not T/S force factor BL.
- Mounting geometry
- Overall frame dimensions, baffle opening and mounting depth have not been established for machining.
- Source checked
- 2026-10-16
Nominal size and voice-coil diameter are verified. Complete mounting geometry has not been independently checked against a dimensioned original drawing; frame diameter, baffle opening and mounting depth remain unlisted.
Construction, mounting & original reference
Open a section for documented details and its original source.
Original construction and weight
- Frame / cone
- Reinforced cast-aluminium basket and moulded-fibre cone
- Surround
- High-compliance cloth with mechanical resistance
- Coil
- 3-inch edgewound copper ribbon
- Driver weight
- 17.5 lb in the original table; distinct from magnet weight or moving mass
- Fixing layout
- Four equally spaced mounting holes; confirm the original fractional dimensions before machining
No uncertain printed fraction is entered as a verified machining dimension.
Source documentation ↗ · AL-1411-2, page 2
Original cabinet and HF combinations
- Enclosure examples
- 612B, 614B, 825A, 210 and 410, listed for 803B and 515B
- Horn-driver examples
- 802D / 804A with 511A/B or 811B; 288C / 290D with a suitable multicellular horn
- Network examples
- N-800D, N-500C and N-500D; the latter is specified with 802D / 804A
Historical combinations only. Match exact network, impedance, horn and cabinet versions; modern replacement equivalence is not established.
Source documentation ↗ · AL-1411-2, page 2
Thiele/Small parameters
Historical T/S values, including free-air resonance, remain unlisted until corroborated by two credible sources for this exact original variant. Later Altec variants and modern replacements are separate. No complete CAD geometry is established.
Technical sources & availability
Original Altec Lansing literature at Lansing Heritage ↗
Discontinued original Altec historical reference. Used-unit availability, reconing and condition require individual confirmation.
The original document remains at its external source. Confirm the exact unit and original drawing before machining.
Search Altec Lansing references → · Vintage driver directory →