Altec Lansing 604-8K
Altec 604-8K Duplex: original LF/HF construction, network controls, service parts, mounting guidance and clearly identified source discrepancies.
Front viewDriver specifications
- Type
- Coaxial Duplex
- Nominal size
- 16 in
- Nominal impedance
- 8 Ω
- Overall diameter
- 406.4 mm
- Sensitivity
- 98.5 dB SPL — 1 W / 1 m, band-limited pink noise 500 Hz–3 kHz, reference 20 μPa; original test at 3.16 m referred to 1 m.
- Published range
- 60 Hz–20 kHz
- Power
- 75 W — AES-style pink-noise system test, 60 Hz–20 kHz, 6 dB crest factor, two hours.
- Crossover
- 1500 Hz
- Document revision
- Revision 5, April 1992
Two-way Duplex driver with a 60° × 40° horn. Specifications are from Altec’s original revision 5 document. The 604-8K is kept separate from other 604 variants.
Construction, mounting & original reference
Open a section for documented details and its original source.
Original two-section construction
- Low-frequency section
- 16-inch cone; 3-inch edgewound copper-ribbon coil and 5.6 lb ferrite magnet
- High-frequency section
- Coaxial 902 compression driver; 1-inch outlet and 1.75-inch aluminium-ribbon coil
- Horn
- 60 × 40 degree Mantaray constant-directivity horn
- HF magnet
- 2.5 lb ferrite magnet
LF and HF voice-coil diameters are distinct; the 1-inch HF outlet is not its coil diameter.
Source documentation ↗ · Revision 5, pages 1 and 6
Original network, mounting and service references
- Network
- 1500 Hz two-way; original LF slope 12 dB/octave and HF slope 18 dB/octave
- EQ controls
- EQ released: HF attenuation. EQ engaged: upper control for HF, lower control for midrange
- Mounting
- Front or rear; original instructions recommend front mounting and eight fixing bolts
- HF diaphragm reference
- 34647 in the original document
- LF cone-kit reference
- R-604-8K
- Accessory enclosure
- 5191-X vented enclosure; six cubic feet (169.8 L) in the original specification
Service part numbers are original references, not a claim of present availability or interchangeability. Read the original mounting and wiring instructions.
Source documentation ↗ · Revision 5, pages 1–3
Published-source discrepancies
- Depth
- The document prints 18.2 inches alongside 22.38 cm; inconsistent units, so no verified mounting depth is entered
- T/S table
- Its printed Qts does not agree with the Qes/Qms relationship; values remain withheld
- Weight conditions
- 34 lb net and 42 lb shipping both include the network, not just the bare driver
- Response context
- Published plots are measured in a six-cubic-foot vented enclosure
Exact variant and measurement conditions matter. No correction to ambiguous printed specifications is invented.
Source documentation ↗ · Revision 5, pages 3 and 5
Thiele/Small parameters
Vintage T/S values are withheld pending independent corroboration. The original table also contains a total-Q value inconsistent with its electrical and mechanical Q values. Mounting cutout and depth remain withheld; the printed depth uses conflicting units.
Availability & sources
Historical Altec variant. Used-unit condition and seller availability are not verified.
Original Altec technical document ↗The document stays at the external archive; its scans are not reproduced here. The photograph retains its own CC BY-SA 4.0 licence; SpeakerFoundry’s original-content notice does not restrict that licence.