◉SpeakerFoundryFREE DRIVER RESOURCES / 01
DISCONTINUED DRIVER REFERENCE

Altec Lansing 515-8GHP

Altec 515-8GHP 8-ohm vintage horn woofer: original enclosure-dependent response/sensitivity, aluminium-ribbon coil and front/rear mounting context.

PDF / documentation ↗

Driver specifications

Type
Woofer
Nominal size
16 in
Impedance
8 Ω
Overall diameter
406.4 mm
Depth
169.86 mm — Rear mounting: 6 11/16 in. Front-mount depth: 5 7/8 in (149.23 mm).
Published range
60–4000 Hz — In the Altec 828G enclosure; low-frequency endpoint is −3 dB. Other enclosures have different ranges.
Published power
200 W — AES-style noise rating: 6 dB crest factor, 60–600 Hz band limit, power calculated as E²/R.
Sensitivity
104.5 dB SPL — 1 W (E²/R), band-limited pink noise 100–1000 Hz, free field on axis at 4 ft (1.2192 m), in the Altec 828G enclosure; not a 1 m rating.
Voice-coil diameter
76.2 mm
Document
515-G series, Revision 1, AL-2422, print code 486-5M

Ferrite low-frequency horn driver. Enclosure-dependent response and sensitivity are shown for the 828G configuration. The 8G, 16G and 8GHP variants retain their own impedance and power ratings.

Construction, mounting & original reference

Open a section for documented details and its original source.

Exact model construction and rating
Variant
515-8GHP; 8 ohms nominal
Voice coil
3-inch edgewound aluminium ribbon
Frame / suspension
Die-cast aluminium frame and low-distortion cloth suspension
Magnet
Ferrite; 132 oz magnet weight, distinct from 30 lb driver weight
Original noise rating
200 W (40 V in original table); 60–600 Hz pink noise, 6 dB crest factor

Power is calculated with the original E²/R method. 515-8G, 515-16G and 515-8GHP remain separate variants.

Original Altec documentation ↗ · AL-2422 Revision 1, pages 1–2

Enclosure-dependent reference conditions
828G
60–4000 Hz; 104.5 dB
816A
70–4000 Hz; 103.5 dB
817A
65–4000 Hz; 106 dB
210/211
55–4000 Hz; 108.5 dB

Each low-frequency endpoint is the original −3 dB point for that enclosure. Sensitivity uses 1 W of 100–1000 Hz pink noise measured on axis at 4 feet in free field; not a 1 m rating or a modern cabinet alignment.

Original Altec documentation ↗ · AL-2422 Revision 1, page 2

Mounting drawing and unresolved cutout
Front-mounted depth
5 7/8 inches (about 149.2 mm)
Rear-mounted depth
6 11/16 inches (about 169.9 mm)
Fixing layout
Eight slots at 45-degree intervals
Cutout conflict
The table and drawing disagree on the inch opening; printed metric conversions also disagree, so generic cutout remains unfilled
Excursion distinction
Maximum before-damage peak-to-peak excursion is separate from linear Xmax; no historical T/S values are newly entered

Use the original drawing and physical unit for fit checks. These reference dimensions do not establish a complete CAD model.

Original Altec documentation ↗ · AL-2422 Revision 1, pages 2 and 4

Thiele/Small parameters

Historical T/S values remain unpublished until corroborated by two credible sources for this exact variant. Baffle cutout is withheld because the table, drawing and printed metric conversions disagree. Depth is specified separately for front and rear mounting.

Availability & sources

Discontinued historical driver. Used-unit availability and condition are not verified.

Original Altec technical document ↗

Original scans and CAD files remain with their external sources.

Search Altec Lansing drivers →