SpeakerFoundry
VINTAGE DRIVER REFERENCE

Altec Lansing 416-8B

Original 15-inch nominal Altec 416-8B 8 Ω woofer with a 16-inch frame, Alnico motor and edgewound copper ribbon coil. Pink-noise power and sensitivity keep their original bandwidth, distance and enclosure conditions; the two-driver 815A figure is kept separate.

PDF / documentation ↗

Driver specifications

Brand
Altec Lansing
Type
Woofer
Nominal size
15 inches — nominal; 16-inch frame
Nominal impedance
8 Ω
Original document
Altec AL-1852-2, print code CP-279-2.5M; no explicit publication date stated
Voice-coil diameter
76.2 mm
Voice-coil material / construction
Copper / Edgewound ribbon
Diaphragm / cone material
Moulded fibre
Frame material
Die-cast aluminium
Surround material
High-compliance cloth
Magnet material
Alnico
Power rating
75 W. 75 W continuous pink noise, band-limited 20–1600 Hz. Preserve this historical test rather than relabelling it as AES power.
Published frequency range
20–1600 Hz. Original table gives a uniform 20–1600 Hz response without a numerical tolerance or a named measurement enclosure.
Pressure sensitivity
97 dB SPL. Altec 612C enclosure configuration, on axis at 4 ft from the front of the enclosure; 1 W band-limited pink noise 500–1000 Hz, reference 20 μPa. Not a 1 m or bare-driver rating.
Other enclosure sensitivities
612C: 97 dB SPL; 815A: 103 dB SPL (2 drivers); 816A: 99.5 dB SPL; 825B / 828A: 100 dB SPL. All listed configurations use the original 1 W, 4 ft on-axis 500–1000 Hz pink-noise method. The 815A row expressly contains two units; it is not a single-driver sensitivity. Other rows do not explicitly state unit count.
Magnet weight
2.4 lb
Magnet-weight conditions
Original table magnet weight. Not whole magnetic assembly mass, driver mass or moving mass Mms.
Magnetic-gap flux density
11000 gauss. Original magnetic-gap flux density; not T/S force factor BL.
Overall frame diameter
406.4 mm
Overall depth
177.8 mm (not verified behind-flange depth)
Baffle opening
358.775 mm. Original 14⅛-inch baffle opening; table permits front or rear mounting.
Mounting depth behind flange
Not established from a dimensioned original drawing
Source checked
2026-10-16

Nominal driver size is 15 inches in the original narrative; the frame is 16 inches. Overall frame diameter, 7-inch overall depth and 14⅛-inch cutout use original inch values converted at 25.4 mm/in. Printed centimetres are rounded. Overall depth is not verified behind-flange mounting depth; bolt geometry and machining tolerances require an original drawing.

Construction, mounting & original reference

Open a section for documented details and its original source.

Original construction and mounting
Frame / cone
Reinforced die-cast aluminium frame; moulded-fibre cone
Surround / coil
Resistively damped high-compliance cloth surround; 3-inch edgewound copper ribbon coil
Mounting
Original sheet permits front or rear mounting; four equally spaced fixing holes
Published opening
14⅛ inches (358.775 mm); converted original dimension, not a manufacturing tolerance
Driver weight
17½ lb (7.94 kg in the original sheet); not the 2.4 lb magnet weight
Depth wording
7-inch overall depth in the sheet; behind-flange mounting depth remains unestablished

Check the exact original drawing before machining. Driver net mass, magnet mass and T/S moving mass are separate.

Original technical reference ↗ · AL-1852-2, page 2

Read the enclosure sensitivity table correctly
Test setup
1 W, 500–1000 Hz band-limited pink noise; on axis at 4 ft
612C / 816A
97.0 / 99.5 dB SPL respectively
825B / 828A
100.0 dB SPL
815A exception
103.0 dB SPL is for the enclosure with two drivers, not a single-driver sensitivity

These are original enclosure-dependent readings, not a universal 1 m sensitivity or a prediction for a newly designed cabinet.

Original technical reference ↗ · AL-1852-2, page 2

Thiele/Small parameters

Historical T/S values remain unlisted until corroborated by two credible sources for this exact original variant. Values from later Altec revisions, modern replacements and individual recones are not substituted.

Technical sources & availability

Original Altec literature at Lansing Heritage ↗

Out-of-production original Altec reference. Used-unit availability, original parts, reconing and condition require individual confirmation.

The original sheet remains at its external source. Confirm the exact unit and original mounting drawing before machining.

Search Altec references → · Vintage driver directory →