Altec Lansing 414A
Original 414A 12-inch 16 Ω Altec low-frequency driver, with an Alnico V motor, moulded-fibre cone and edgewound copper ribbon coil. The historical continuous-power and 4 ft sensitivity conditions are preserved.
Driver specifications
- Brand
- Altec Lansing
- Type
- Woofer
- Nominal size
- 12 inches — nominal
- Nominal impedance
- 16 Ω
- Original document
- Altec catalogue sheet AL-1411-2; publication date not stated
- Voice-coil diameter
- 76.2 mm (3 inches)
- Voice-coil material / construction
- Copper / Edgewound ribbon
- Frame material
- Cast aluminium
- Cone material
- Moulded fibre
- Surround material
- High-compliance cloth
- Magnet material
- Alnico V
- Continuous power
- 25 W. Continuous power rating in the original sheet. No AES/RMS noise-test method or bandwidth is given; this is not relabelled as an AES rating.
- Pressure sensitivity
- 99 dB SPL. Published pressure sensitivity on axis at 4 ft (1.2192 m), with 1 W input. Signal bandwidth and enclosure are not specified. This is not a 1 m rating.
- Full-power SPL
- 113 dB SPL. Published SPL at 4 ft using the full 25 W continuous rating, separate from the 1 W sensitivity.
- Published frequency range
- 30–4000 Hz. Published frequency-response endpoints in the original sheet; no response tolerance, measurement enclosure or modern test standard is specified.
- Magnet weight
- 1.8 lb. Magnet weight in the original table; not complete magnetic assembly weight, driver mass or moving mass Mms.
- Magnetic gap flux density
- 10000 gauss. Original magnetic-gap flux density, in gauss; not T/S force factor BL.
- Mounting geometry
- Overall frame dimensions, baffle opening and mounting depth have not been established for machining.
- Source checked
- 2026-10-16
Nominal size and voice-coil diameter are verified. Complete mounting geometry has not been independently checked against a dimensioned original drawing; frame diameter, baffle opening and mounting depth remain unlisted.
Construction, mounting & original reference
Open a section for documented details and its original source.
Construction and mounting identification
- Frame / cone
- Structurally reinforced cast-aluminium basket and moulded-fibre cone
- Suspension
- High-compliance cloth surround with mechanical resistance
- Coil
- 3-inch (76.2 mm) edgewound copper ribbon
- Fixing layout
- Four equally spaced mounting holes; use the original drawing for the bolt-circle and clearances
- Driver mass
- 15 lb in the original table; distinct from the 1.8 lb magnet
Nominal size and basket diameter are not interchangeable. No unreadable fraction is entered as a machining dimension.
Original technical reference ↗ · AL-1411-2, page 2
Original enclosure and horn references
- Bass-reflex cabinet examples
- 612B, 614B, 618B and 622B for 414A
- Original HF options
- 802D / 804A with 511A/511B or 811B; 288C / 290D with a suitable multicellular horn
- Network conditions
- Original literature distinguishes N-800D, N-500C and N-500D; N-500D is specified with 802D / 804A
Historical component combinations only. Exact network, horn, impedance and cabinet version must match; current replacement compatibility is not established.
Original technical reference ↗ · AL-1411-2, page 2
Thiele/Small parameters
Historical T/S values, including free-air resonance, remain unlisted until corroborated by two credible sources for this exact original variant. Later Altec variants and modern replacements are separate. No complete CAD geometry is established.
Technical sources & availability
Original Altec Lansing literature at Lansing Heritage ↗
Discontinued original Altec historical reference. Used-unit availability, reconing and condition require individual confirmation.
The original document remains at its external source. Confirm the exact unit and original drawing before machining.
Search Altec Lansing references → · Vintage driver directory →